| 电缆槽模具安全规程 |
| 添加时间：2018/5/18 17:01:19 浏览次数： |
| 电缆槽模具安全规程 Safety regulations for die of cable grooves 电缆沟沟盖板生产现场必须与水、电、气和易燃易爆、有毒的物品打交道，为了防止在工作过程中发生失火、爆炸、中毒利人身、设备以及质量事故的发生，要注意安全生产。 The production site of the cable ditch and ditch cover must deal with water, electricity, gas and inflammable, explosive and toxic materials. In order to prevent the occurrence of fire, explosion, poisoning, equipment and quality accidents, safety production should be paid attention to. 1、防爆：现场使用的乙炔、氧气等均为易燃易爆气体，稍有不慎，就会发生文火和爆炸，因此对于易燃易爆的气液体的使用必须严格按照操作规程执行。对于潮湿的工具和军件，沟盖板在未经干燥的情况厂，放入加热炉，水蒸气的膨胀，都会产生爆炸或喷小灼伤人员，因此只要是需要入炉的任何器具和零件必须进行干燥。 1, explosion-proof: the use of acetylene, oxygen and other gas are flammable and explosive gas, a slight inadvertent, will happen to fire and explosion, so the use of flammable and explosive gas liquid must be strictly in accordance with the operating procedures. For wet tools and armies, the furrow cover is in the Undry condition, put into the heating furnace, and the expansion of the steam will produce explosion or spray burn personnel, so as long as any equipment and parts in need of the furnace must be dried. 2、防毒：热处理所使用的一些热处理介质均有较强的毒件，再加之齐高温之下产生的有毒气体和生产中产牛的废水，都对人体产生极大的危害。因此沟盖板操作者必须注意穿戴好防护服和防毒面具，生产现场必须保持遇风利抽风，下班后必须注意清洗和清洁工作。 2, antivirus: some heat treatment mediums used in heat treatment have strong toxic components, and the toxic gases produced by the high temperature and the production of middle class cattle are all harmful to the human body. Therefore, the operator must pay attention to wearing good protective clothing and gas mask. The production site must keep the wind and wind. After work, we must pay attention to cleaning and cleaning. 3、防火：必须经常检合牛产现场的电线是否老化、破损和短路，检查油槽内油液是否溢出、泊温是否安全、沟盖板冷却循环系统是否工作可靠，检查现场的大火器材是否完备和正常工作。 3, fire prevention: it is necessary to regularly check the aging, breakage and short circuit of the wire of the cattle production site, check the oil spill in the tank, whether the temperature is safe, whether the cooling cycle system of the groove cover is reliable, and check the complete and normal work of the fire equipment on the site. 润达电缆槽模具具有易脱模、韧性强、寿命长等特点，一般生产量很大的模具，制造时应采用高性能的材料，这样不但能使模具的耐用度得到新的提高水平，这类模具材料还可以进行低真空表面强化处理。模具精度要求高、形状复杂的，润达模具的制造周期较长，模具材料本身的费用远远不如加工费的费用，最后，就是模具的高强度，是否具有耐磨、耐热、耐压的能力，只有强度符合标准的产品才能经得住市场的考验。 The mould has the characteristics of easy demoulding, strong toughness, long life and so on. The high performance material should be used in the manufacture of the mold, which can not only make the die durable get a new level of improvement, but this kind of mold material can also carry on the low vacuum surface strengthening treatment. The mould precision is high, the shape is complex, the manufacturing cycle of the mold is long, the cost of the mold material itself is far less than the cost of the processing fee. Finally, it is the high strength of the mould, whether it has the ability of wear resistance, heat resistance and pressure resistance, only the strength that meets the standard can stand the test of the market. |
| 上一页 电缆槽模具材质 |
| 下一页 电缆槽盖板模具技术要求 |
Copyright © 技术支持：遨游网络